- 1、本文档共6页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
* / 6 05/2002 Draft Control Adjustment NH RM 35 - 5 Draft Control Adjustment 1. Move the position and draft control levers (2 and 1, respectively) fully backward, to touch the quadrant stop. 2. Disassemble the eccentric pin (1, previous slide) retaining the draft control internal lever. Insert tool no. 293981 (1) in the pin hole. Note: Using a lever as shown in the slide, unload the control valve rod spring to assist eccentric pin removal and subsequent installation of service pin (1). 3. Tighten the screw (2) of tool no. 293980 (1). 4. Disconnect the threaded rod (1) at the draft control internal lever. 5. Turn the threaded rod (1, Fig 51) until face of the rod is aligned with the outer reference plane of tool no. 293979 (2). Note: One turn of the threaded rod corresponds to moving the tool rod (1) by approximately 3 mm. 6. Remove pin tool no. 293981 (1, Fig. 49) and install the eccentric pin (1, Fig. 53) taking care that the pin cam is turned towards the front of the tractor. Tighten the retaining ring nut to the lift casing. * / 6 * * NH RM 35 - 5 Draft Control Adjustment 1. Move the position and draft control levers (2 and 1, respectively) fully backward, to touch the quadrant stop. 2. Disassemble the eccentric pin (1, previous slide) retaining the draft control internal lever. Insert tool no. 293981 (1) in the pin hole. Note: Using a lever as shown in the slide, unload the control valve rod spring to assist eccentric pin removal and subsequent installation of service pin (1). 3. Tighten the screw (2) of tool no. 293980 (1). 4. Disconnect the threaded rod (1) at the draft control internal lever. 5. Turn the threaded rod (1, Fig 51) until face of the rod is aligned with the outer reference plane of tool no. 293979 (2). Note: One turn of the threaded rod corresponds to moving the tool rod (1) by approximately 3 mm. 6. Remove pin tool no. 293981 (1, Fig. 49) and install the eccentric pin (1, Fig. 53) taking care that the pin cam is turned towards the front
您可能关注的文档
- 连锁零售企业采购实务商品订单计划制定评估商品采购订单需求.pptx
- 连锁企业品类管理零售商表现评估零售商表现评估.pptx
- 联合申报院校课程资源塑料注射成型、湖北工业职业技术学院塑料的注射机吉利培训.ppt
- 临床疾病概要(外科学)临床疾病概要(外科学)胆囊结石.pptx
- 临床疾病概要过敏性紫癜的病因与发病机制过敏性紫癜的病因与发病机制.pptx
- 临床疾病概要甲状腺功能亢进临床表现和治疗甲状腺功能亢进症的临床表现和治疗.pptx
- 临床疾病概要慢性支气管炎的临床特点与治疗慢性支气管炎的临床特点与治疗.pptx
- 临床检验基础技术血细胞分析仪的操作方法、注意事项血液分析仪的校准.ppt
- 临床免疫检验技术第七单元甲肝抗体(IgM)检测甲肝的测定.ppt
- 临床实践技能呼吸系统疾病呼吸系统病例分析-2.pptx
文档评论(0)