- 1、本文档共56页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
亲,这是专业人士做的,绝对合格的。请放心。已经通过答辩!
摘 要
关键词:;;;
Abstract
Printer gear were widely used in industrial production. In order to adapt to the users of the mold manufacturing which become high precision, short delivery time, low-cost requirements, the mold industry is widely used digital manufacturing technology to accelerate the advancement of technology. To short the mold manufacturing cycle and reduce the cost of the mold, CAD / CAM technology must be used. 牋牋 Designing mold , develop printer gear master injection mold design and molding process of the products of choice; the general gear mold design capability, quality analysis and process improvement, ability to improve the design of injection mold structure; commonly used software, and a combination of the actual design of the same.牋牋The mold design process analysis, process characteristics of the printer gear, and PA66 material molding process characteristics, different molding program and compared in the mold design process, to take the best molding program, at the same time detailed mold structure and calculation. Mold can be achieved through the entire design process show that the requirements for the processing of the plastic parts. The main task is to design under the title injection mold design of plastic gears. An injection mold is designed to produce the gear plastic products to automate increase production. Finally, the molded part of the mold process analysis equipment check, and also describes the working principle of the mold, the mold equipment also made a brief introduction.
Key words: Mold Design; Printer gear; Injection Molding
目 录
摘 要 II
Abstract III
目 录 IV
1 绪 论 1
1.1 本课题的研究内容和意义 1
1.2 国内外塑料成型模具发展概况 1
1.3本课题应达到的要求 3
1.4 本课题应达到的要求 3
2 打印机齿轮成型工艺性分析 4
2.1 打印机齿轮分析 4
2.2 注射成型过程及工艺参数 5
2.3 PA66的性能分析 6
3模具结构形式的拟定 7
3.1 分型面位置的确定 7
3.2 确定型腔数量及排列方式 8
3.3 模具结构形式的确定 8
4 注射机的选用 10
4.1 所需注射量的计算 10
4.2 注射机型号的选定 10
4.3 型腔数量及注射机有关工艺参数的校核 11
4.3.1 型腔数量的校核 11
4.3.2 注射机工艺参数的校核 12
4.3.3 安装尺寸校核 12
4.4 开模行程和推出机构的校核 13
4.4.1 开模行程校核 13
4.4.
您可能关注的文档
- C6140普通车床主轴变速箱设计说明书.doc
- 包装机推包机构设计说明书.doc
- 波纹管成型机的设计说明书.doc
- 财务管理系统应用程序论文.doc
- 财务管理系统应用程序设计论文.doc
- 餐饮酒店管理系统论文.doc
- 仓储物资管理系统设计论文.doc
- 仓库即时查询系统论文.doc
- 操作系统课程教学网站论文.doc
- 槽轮间歇回转机构的设计说明书.doc
- 第12课 我们小点儿声 课件 二年级道德与法治上册(部编版).ppt
- 11.2我从哪里来(教学课件)二年级道德与法治下册(统编版).ppt
- 第10课 我们不乱扔 课件 二年级道德与法治上册(部编版).ppt
- 1.3过好我们的课余生活 课件五年级道德与法治上册(部编版).ppt
- 第四单元《法律保护我们健康成长》大单元整体学程设计道德与法治六年级上册统编版.pdf
- 第十一课:多姿多彩的民间艺术(分层练习)四年级道法下册 部编版.pdf
- 第八课:大家的“朋友”(分层练习)三年级道法下册 部编版.pdf
- 第5课 我爱我们班 课件 二年级道德与法治上册(部编版).ppt
- 第二单元 我们是公民 大单元整体学程设计道德与法治六年级上册统编版.pdf
- 人教部编版二年级语文下册第五单元单元教学课件.ppt
文档评论(0)